Clone A Willy Review
Kit Contains:
Molding powder
body safe silicone (2 jars)
Vibrator
stir stick
molding tube
thermometer
How to use:
Get everything you need to start. Measuring cup, mixing bowel, spoon
Get a erection (use cock ring or pump)
place tube beside penis cut to proper size
Get 1 3/4 cup of water from sink, run with thermometer and get it at 98°
Mix with powder (h20 first, then add powder) quickly
option 1: pour into tube and shove cock into it or option 2 (from another bloggers review) put cock in and pour mixture into tube onto your cock.
allow to harden for at least 2 min. before pulling penis out
let mold sit for 4 hrs or more before adding silicone
mix the 2 jars of silicone together in a 8 oz. (or larger) disposable container
Make sure to stir thoroughly for at least 2 min. and pour into mold
make sure to pour any excess water out of mold before adding silicone
take a small piece of cardboard 4×4 and cut a × into center
push vibrator into × so only screw cap sticks out one end
carefully insert into center of your mold so the cardboard rests flat on rim of tube
let sit for 24 hrs at least, touch silicone and make sure it is hard
carefully remove mold, remove cardboard, cut off any bumps
Clean with soap and water
I choose to use a old potato salad container to mix both My Review/Experience: So this is going to be my second attempt at cloning a penis. My first attempt failed, I did it the way that I was told in the instructions, followed it to a T. But my bf at the times penis wasn't hard enough and wasn't able to push into the molding powder, by the time I got it hard the powder had hardened. So today I decided to go about it differently I read in a blog by a guy to cut the end off, and pour the mixing powder into it, onto my mans penis. So that is what we did. It worked out except my man got upset over some of it coming out the top from me pouring to fast. He acted as though it was ruined and just to throw it out (perhaps because he lost an erection, but I told him nope I want to put the silicone in and see what I get. So I added the black lid to the open end and sat it to harden.
This is the mold right now, it has a hole from where skin touched the side
so far I feel like the mold itself looks good, I looked in under good light and it totally has the head/pee hole looking perfect...hopefully the side looks as good. I ended up letting it sit for 6-7 hrs. instead of 2-4 hrs. just to be on the safe side...but then read that it may cause shrinkage to over dry it, so then i panicked and got to silicone mixing!!!!
I wanted it to be a dildo not a vibrator, and i was hoping i would have enough but i did not. I had about 3/4 inch of space left without silicone and i scraped it all out of the jars and mixing bowel. So then i was left with the choice, make my boyfriends penis a little shorter then it really is....or add the vibrator and risk messing it up and having vibe poking out the side (read of that happening). I chose the later.
I would have preferred to use a stronger strength vibe, or a egg even. I really would have loved to use one of those eggs with the wire that attaches to a remote i would have put it down in the head or in the middle and then only a wire would be coming out of my clone instead of a screw top. Next time i do this i am going to get an egg to try putting in it!!! I know if I try again (third times a charm) it will be perfection!!! I already anticipate some errors in my mold, because of the holes in my mold silicone got in the side of the tube, so I am going to have to cut that deformity off when its done setting, but I am praying that it works out the way I am thinking in my head. We will see. No matter, i will want to try this again!!!
So today I got to finally open it, i waited 36 hrs. instead of 24 hrs. i was nervous that it wouldn't come out because i had read about so many peoples bad experiences trying to make there's. But i was blessed. Even my silly fear of the silicone on the side of the tube making a mess was just that, a silly fear! It came out perfect and easily!!! The mold did rip apart in the removal because i was trying to be careful and not harm the dildo!!
the mold ripped from the removal!
Here are pictures of my perfect clone a willy!!
It looks so frickin good. I am proud of it!! I feel like a artist!! I just had to trim some bumps off it with mini scissors and wash it and then it was ready to take for a test drive!!
It isn't as large as my boyfriend is normally its like a semi-hard one, but it measures a little over 6 inches insertable length. The vibrations are actually able to be felt but mild. But it is nice. This penis is firm like a really hard cock. There is no rubber smell. Its really great and feels amazing.
my boyfriend loves that it is a mold of his penis he is amazed at how good it came out!!!
we love it!!!!
about cloning a penis
also this is my fave review slutty girl problems, clone a willy review